Williams 6008531 Owner's Manual download pdf (Page 4)

Safety Rules

WARNING: Read these rules and the instructions

carefully. Failure to follow these rules and

instructions could cause a malfunction of the

furnace. This could result in death, serious bodily

injury and/or property damage.

INSTALLATION MUST CONFORM TO LOCAL CODES. IN THE

ABSENCE OF LOCAL CODES, INSTALLATION MUST

CONFORM TO THE NATIONAL FUEL GAS CODE, ANSI Z223.1.

THE APPLIANCE, WHEN INSTALLED MUST BE

ELECTRICALLY CONNECTED AND GROUNDED IN

ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE

OF LOCAL CODES, WITH THE CURRENT NATIONAL

ELECTRICAL CODE ANSI/NFPA NO. 70.

In Canada:

1. Installation must conform to local codes or, in

the absence of local codes, the current

CAN/CGA B149 installation code.

2. The appliance, when installed, must be

electrically connected and grounded in

accordance with local codes or, in the absence

of local codes, with the current CSA C22.1

Canadian Electrical code.

3. Field conversions for high altitude are not

permitted in Canada.

4. Reference is made in this manual regarding gas

type as L.P.G. Be advised that L.P.G. is not

available in Canada, refer to propane/L.P. Gas.

1. Use only manufacturer's replacement parts. Use of any

other parts could cause injury or death.

2. DO NOT install this furnace where it could be isolated by

closing doors to the heated space.

3. DO NOT install this furnace in a travel trailer or

recreational vehicle.

4. MAINTAIN all clearances specified in section "Locating

Wall Furnace and Thermostat".

5. BE SURE this furnace is for type of gas to be used.

Check the rating plate by the gas valve in the lower

cabinet. Do not change it to use other gases without the

proper manufacturer’s Gas Conversion Kit.

6. For natural gas, the minimum inlet gas supply pressure

for the purpose of input adjustment is 5" water column.

The maximum inlet gas supply pressure is 7" water

column.

For L.P. Gas, the minimum inlet gas supply pressure for

the purpose of input adjustment is 11" water column. The

maximum inlet gas supply pressure is 13" water column.

7. Any safety screen, guard or parts removed for servicing

this appliance must be replaced prior to operating the

appliance to avoid property damage, bodily injury or

death.

8. Install the furnace vent directly to the outdoors so that

harmful combustible flue gases will not collect inside the

building. Follow the venting instructions for your type of

installation exactly. Use only the type and size of vent

pipe and fittings specified.

9. BE SURE to provide for adequate combustion and

ventilation air. The flow of this air to the furnace must not

be blocked.

10. NEVER vent flue gases into another room, a fireplace or

any space inside a building. This could cause property

damage, bodily injury or death.

11. Never test for gas teaks with an open flame. Use a soap

solution to check all gas connections. This will avoid the

possibility of fire or explosion.

12. ALLOW the furnace to cool before servicing. Always shut

off electricity and gas to furnace when working on it. This

will prevent any electrical shocks or burns.

13. DUE TO HIGH TEMPERATURES, locate the furnace out

of traffic and away from furniture and draperies.

14. ALERT children and adults to the hazards of high surface

temperatures and warn them to keep away to avoid

burns or clothing ignition.

15. CAREFULLY supervise young children when they are in

the same room with the furnace.

16. DO NOT place clothing or other flammable material on or

near furnace.

17. INSTALLATION and REPAIR must be done by a qualified

service person. The appliance should be inspected

before use and at least annually by a professional

service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material,

etc. It is imperative that control compartments, burners

and circulating air passages be kept clean.

18. BEFORE INSTALLING: To avoid electrical shock, tum off

electrical circuits that pass through the wall where you

are going to install the furnace.

19. BE AWARE of good safety practices by wearing personal

protective equipment such as gloves and safety glasses

to avoid being injured by sharp metal edges in or around

furnace and while cutting or drilling holes in wood and/or

sheet metal.

WARNING: Do not use this furnace if any part has

been under water. Immediately call a certified

service technician to inspect the furnace and to

replace any part of the control system and any gas

control which has been under water.

WARNING: Do not install any of these furnaces

(Natural or L.P. Gas) in mobile homes, trucks or

recreational vehicles.

1 2 3 4 5 6 7 8 9 ... 35 36

Comments to this Manuals

No comments

Williams 6008531 Owner's Manual Page 4

Comments to this Manuals

Related products and manuals for Water heaters & boilers Williams 6008531